Camera Slider Schematics

Wiring diagram for My camera Slider build.

Camera Slider Schematics

  • The stepper motors wiring is dependent on witch stepper motor you use, so for that you have to examine how the wire it to the EasyDriver.
  • Also the relay is wired but how you wire it to your camera is also something you have to examine to your specific camera. I ordered a cheap camera trigger from China for about 3-5 Dollars, and took apart to see how the wiring work, and used the wire from that.
  • The TFT display is not on the diagram because it is just a shield you put on top of the Arduino Uno.

The Arduino code can be found here Arduino Code

And just to mention it, i do not take any responsibility to brigged hardware or buggy code.

Related posts

Battery Pack From Old Laptop

Battery Pack From Old Laptop


Battery Pack From Old Laptop

Make a 3S battery from old Laptop Battery I needed a battery for my gimbal, and wanted to make it as small as possible and still have enough power to run the gimbal properly. The top bar of the gimbal is an old carbon bike handlebar. And I thought it would be cool to have the battery inside...

Commodore 64 back to life

Commodore 64 back to life


Commodore 64 back to life

Commodore 64 back to life. My brother found an old Commodoe 64 in his basement, and asked me if i wanted to have it.I got this box from him, it was very dusty, and yes that is a printer. I was not sure what to expect, but went ahead and connected it to the TV, and it actually turned...

Making a Concrete Table.

Making a Concrete Table.


Making a Concrete Table.

Homemade Concrete table. I was looking for a new coffee table for my living room, because the old one was well used, but i could find one i like, or could afford.So what to do ?  Well i decided to build my own and it went quite well i think :)I wanted something with a rustic look, so...

Homemade Camera Gimbal Finished

Homemade Camera Gimbal Finished


Homemade Camera Gimbal Finished

Homemade Camera Gimbal Finished (Almost) So my Gimbal project is reached a state where i can call it almost finished. Of course such a project will always have place for improvements, But for now it is in a working order.A lot of people have been asking me for the drawings / plans for the...

Arduino code for the Camera Slider.

Arduino code for the Camera Slider.


Arduino code for the Camera Slider.

//Recently i have gotten some request for sharing the Arduino code for my homemade camera slider.To start with i just want to say, I'm no master in this, so there can be bugs, and the code is still early and not complete. Recently i haven't had much time for these kind of projects...

DIY Gimbal Project (AlexMos) Worklog

DIY Gimbal Project (AlexMos) Worklog


DIY Gimbal Project (AlexMos) Worklog

Today i ordered the first parts for my Gimbal project.I have ordered Battery, Motors, and Controller, when i receive the parts i can begin to design the frame. The Gimbal is going the be used with a Sony A6000 Camera.This is the fist gimbal i ever made so this is Not a how to guide(at...

8 Comments

  1. clemens August 15, 2016
    Reply

    hey 😉

    what accu do u use ?

  2. clemens August 18, 2016
    Reply

    thanks

    what does it mean that u plugged in the power to the usb port ?
    can u pls send me a detail pic of that

    i will make my own slider too
    i will send u pics of my finish working slider 🙂

    thanks

    • Paw Pedersen August 18, 2016
      Reply

      That is a mistake in the picture, the power is connected to the power plug of the Arduino. – I will make a new picture.

      That is Cool, looking forward to seeing your slider.

  3. clemens August 18, 2016
    Reply

    ah ok thanks, i think next week im finish with the slider

    today i order the stuff

  4. Shakoor September 27, 2016
    Reply

    Best project . I will surely make this . Just wanted to know how is camera connected to the relay ? Would be great if you could through wireless remote and infrared trigger in it . I might need your help as I am going to make this . Great Job !

  5. Paw Pedersen September 29, 2016
    Reply

    I use a usb micro USB cable, i bought a cheap wired remote and took apart to and cut the wire to it.

  6. Rogier Hoogmolen September 16, 2018
    Reply

    for some reason i’m not able to get the relay to work. i’ve got everything working and modified the TFT display because i’ve got an other one.

Leave a Reply